Dash & Silencer

Pete&Matt · Post by **Pete&Matt** » Mon Sep 03, 2007 12:57 pm

Does anyone know if there is a standard template dash on the market that fits well in the Stylus?
Also is the "fury type" silencer from Car Builder Solutions the same as Tim supplies?

Having been trying to get hold of Tim for 2 weeks now and given up! I like the dash he does, and know it fits well etc, but we want to get on with our build and are being held up by not getting hold of bits!

Cheers

Matt

stylussprinter · Post by **stylussprinter** » Mon Sep 03, 2007 1:59 pm

Pete&Matt wrote:Does anyone know if there is a standard template dash on the market that fits well in the Stylus?
Also is the "fury type" silencer from Car Builder Solutions the same as Tim supplies?

Having been trying to get hold of Tim for 2 weeks now and given up! I like the dash he does, and know it fits well etc, but we want to get on with our build and are being held up by not getting hold of bits!

Cheers

Matt

SILENSER

That depends entirely on what engine you fit / manifold you fit and therefore what primary lengths/diam' --- leading to

size collector = through pipe

My advice would be to fit the longest/biggest diameter silenser that will go in without touching the f/glass by 10mm minimum. Also if you can afford it have it repackable , it will save you money in the long run plus be better if you want to track it as the DB's limit is forever being lowered

DASHBOARD

Don't know whether the Fury is fundamentally the same dimensions behind the screen BUT in theory it may well be because FURY & STYLUS both use the Elan screen . It's the top you really need I presume then the front is easily made from carbon fibre or look a like OR alloy covered with 'stick 'on carbon layer etc.
If you're really stuffed , I could take mine off and try to get some made

Pete&Matt · Post by **Pete&Matt** » Mon Sep 03, 2007 2:13 pm

The Car Builders Solution silencer is a 5" diameter item. Repackable too and all in stainless. Its mainly going to be for road use, so need to be carefull on the DB's! We are going to get a mainfiold made for it, as all enquires have lead to no where. Its the Toyota 4age 1600 lump we are running. I will put a flexi joint in line too, but the manifold will mate up where ever it ends up! Where did your silencer come from?

I might try Fisher Fury and see what dashes they do, i expect they are similar. Dont want to put you to the agro of taking all of yours out! Would like a carbon effect one anyway! Will see what i can find out!

cheers for your help as always!

Matt

Pete&Matt · Post by **Pete&Matt** » Mon Sep 03, 2007 2:38 pm

just spoken to Fisher Cars
They can do a 2 piece dash for £36! or a GRP moulded type for £80
they reakon that it should fit too. All their dashes have to be fitted to each car anyway, so thats even better.

They can do a silencer for £137. same as what Car Builder Solutions do!

will give it to the end of the week for Tim to get in contact, or they get our business!

stylussprinter · Post by **stylussprinter** » Mon Sep 03, 2007 2:53 pm

Pete&Matt wrote:The Car Builders Solution silencer is a 5" diameter item. Repackable too and all in stainless. Its mainly going to be for road use, so need to be carefull on the DB's! We are going to get a mainfiold made for it, as all enquires have lead to no where. Its the Toyota 4age 1600 lump we are running. I will put a flexi joint in line too, but the manifold will mate up where ever it ends up! Where did your silencer come from?

I might try Fisher Fury and see what dashes they do, i expect they are similar. Dont want to put you to the agro of taking all of yours out! Would like a carbon effect one anyway! Will see what i can find out!

cheers for your help as always!

Matt

My silenser is SBD's silenser from their dyno ' as they were upping the power they needed to test so went to a 7 inch item. Mine is 6 inches x 24 inches with a 2.75 inch internal diameter through pipe and 3 inch exit . Don't think you'll need more than 2 inch through pipe , possibly 2.25 inch if you intend upping power to 160 or more bhp. 200bhp is around the max for the 4age. When you pack the silenser use just a very thin layer of stainless wire wool then BASALT packing but only just gently prodded with a bit of dowling to make it firm NOT tight . This material enabled me to use my existing silenser rather than a new 7 inch to cope with the latest power hike

Tested at 4800 rpm (3/4 of max = 6500 rpm

I lied

) it registered 98 db's

The ' e ' glass would never have got it to that --- more like 105 at best .
Regarding fixing to the chassis ---- bolt a nice alloy angle to the lower seat pan area (outside) then pop a rubber bobbin on top with your silenser bracket also on top of that . Mine's been mounted like that for 5 years competition and no other fixing apart from the manifold being bolted to the engine ------------ never broken ---- no problems

My dash top comes out in 5 minutes flat mate

so if you need to copy it

Rob.

Pete&Matt · Post by **Pete&Matt** » Mon Sep 03, 2007 3:09 pm

thanks rob. May well take you up on the offer of the dash top! quite fancy making my own!

Nissanman · Post by **Nissanman** » Tue Sep 04, 2007 6:13 pm

I got my silencer from these chaps, apparently they made them for Tim, they certainly didn't need any dimension (width and length) just the bore (mines 2.5 inch and apparently good for <350bhp):

http://www.powerspeed.co.uk/ContactUs.html

Pete&Matt · Post by **Pete&Matt** » Tue Sep 04, 2007 6:33 pm

how much did you pay for it?

drhunter · Post by **drhunter** » Tue Sep 04, 2007 7:19 pm

How about this dash?!

Pete&Matt · Post by **Pete&Matt** » Wed Sep 05, 2007 9:18 am

not over keen on that!

what i like is the flat carbon dash that Tim used to do! but he no longer does them unfortunatly!

drhunter · Post by **drhunter** » Wed Sep 05, 2007 10:16 am

do you have any photos?
I'm looking to replace mine when I do the engine.

se7ensport · Post by **se7ensport** » Wed Sep 05, 2007 10:36 am

If you are after a flat carbon dash I'd get in contact with this guy http://www.locostbuilders.co.uk/viewthr ... ?tid=73445

seems very competitively priced.

Pete&Matt · Post by **Pete&Matt** » Wed Sep 05, 2007 11:10 am

thanks for the link. looks intresting!
Maybe if Rob can do me a template of the top of his dash and give me some dims, then i can draw it all out etc and get this guy to machine it all in carbon!! hmmmmmm

whiterabbit · Post by **whiterabbit** » Thu Sep 06, 2007 8:17 pm

I have an SSC dash in stock not fitted to the car yet. I dont want to undermine Tims business, he needs our support by all accounts, but it would be relatively easy to trace or measure if this a way forward for you.

If the business is going up for sale, I hope Tim might offer it here first, maybe a co-operative of owners ? What are your thoughts ?

Steve.

Pete&Matt · Post by **Pete&Matt** » Thu Sep 06, 2007 9:13 pm

you have a PM

clubstylus

Dash & Silencer

Dash & Silencer

Re: Dash & Silencer

Template Possible