What seats???

PeteC · Post by **PeteC** » Tue Feb 26, 2008 1:50 pm

As the subject line say!!
I am planning on my Stylus being a road car with a track day/sprint now and again so am looking for comfort as well as low weight and support. What was Tim or the likes of Fisher offering? I have seen some "Roadster" seats in some mags designed for "narrow bodied kits", that I like the look of, but thought I would ask what you all have first.

stylussprinter · Post by **stylussprinter** » Wed Feb 27, 2008 12:10 pm

PeteC wrote:As the subject line say!!
I am planning on my Stylus being a road car with a track day/sprint now and again so am looking for comfort as well as low weight and support. What was Tim or the likes of Fisher offering? I have seen some "Roadster" seats in some mags designed for "narrow bodied kits", that I like the look of, but thought I would ask what you all have first.

You'd be amazed how comfortable my f/glass bucket racing seat is even without padding. £90 from one of the 7 type kit companies at Exeter 3 years ago.

Cerberus · Post by **Cerberus** » Wed Feb 27, 2008 6:02 pm

The fibreglass seats in mine are comfy enough with no padding, depending on how tall you are you may have trouble with padding, when i tried Alex's car my line of vision was inline with the top of his screen i think he has changed his seats now

Phil

PeteC · Post by **PeteC** » Sat Mar 01, 2008 1:47 pm

Thanks Rob and Phil, it seems you are the only people with seats in there cars!!! Anybody else???
I must admit the race seats do look damn good, was just a little worried about distance/comfort, but in there favour is cost, weight, looks and they are waterproof!!

stylussprinter · Post by **stylussprinter** » Sat Mar 01, 2008 1:59 pm

The reason they're comfy is that they're body shaped and hold you so the padding's not needed really

drhunter · Post by **drhunter** » Sat Mar 01, 2008 5:56 pm

Mine has what I think are the donor vehicles seats re-upholstered in vinyl.
They're confy enough for short journeys but I get thrown about a lot when thrashing the car and they make the drving position too high.
If I sit comfortably I have the top of the windscreen in the middle of my eyeline and if the roof's on I have to slouch to not have my head holding to roof up

Triton on locostbuilders has a good reputation - I'd buy some if I knew they'd fit my fat backside ( all 16.5 stone of me)

http://www.locostbuilders.co.uk/viewthr ... ?tid=83971

se7ensport · Post by **se7ensport** » Sat Mar 01, 2008 11:54 pm

these are great if you like tight fitting seats
http://cgi.ebay.co.uk/FIBREGLASS-KIT-CA ... dZViewItem

stylussprinter · Post by **stylussprinter** » Sun Mar 02, 2008 1:15 am

se7ensport wrote:these are great if you like tight fitting seats
http://cgi.ebay.co.uk/FIBREGLASS-KIT-CA ... dZViewItem

Almost identical to mine --- very comfortable

PeteC · Post by **PeteC** » Sun Mar 02, 2008 4:57 pm

Thanks for the info guys. That last manufacturer is in Southport and so not far away at all, may have to have a little trip out with the cheque book!!

PeteC · Post by **PeteC** » Tue Nov 18, 2008 2:54 am

Better late than never, I took that trip to Southport and spoke to Keith of J K Compoites.com, a very helpful man and a petrol head as well! Took a template of the floor from the stylus on a piece of wall paper and Keith showed me how much room was available by placing one of his seats on top. I ordered two sizes, 380mm for the drivers seat (to go on runners) and 400mm for the passenger (which will be fixed). One week later I went back to collect my seats with the velcro attached upholstery. I am now a very happy bunny and would recommend them for their quality product and friendly service

Keith and Jordan can be contacted via web site or tel:-01704 569730
Pete C

Post by **Werner Van Loock** » Tue Nov 18, 2008 12:22 pm

2 compnaies that supply this kind of seats are:

http://www.tritonraceproducts.co.uk/ (click on seats at the top)
and
http://www.jkcomposites.com/ (click on sevens dimensions)

Antnicuk · Post by **Antnicuk** » Tue Nov 18, 2008 11:26 pm

do you have any pictures

PeteC · Post by **PeteC** » Tue Nov 18, 2008 11:40 pm

Can't find the lead for my camera so I can't upload any pics at the moment, but the ones shown on JKcomposites web site labelled "sevens dimension", the ones with the horizontal stripes are the ones I went for. The only difference is that they now mould a second skin on to the base/lumbar area with 8mm threads for added support for seat runners.

stylussprinter · Post by **stylussprinter** » Wed Nov 19, 2008 11:12 am

I didn't use seat runners , it just takes up space that you've been trying to lose (lower/seat

) Bolt it in with spacers to keep the bulge of the seat pan off the floor

Sit in the car with a plank or polyurethane the right thickness behind the seat till you find the ideal position. Finally Sikaflex a spacer on the back of the seat , level with the boot chassis cross member to stop flex

Unless of course you intend others to be able to drive

Anyone who drives mine has to be my height or put up with it

clubstylus

What seats???

What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???

Re: What seats???